body side molding – the DAILY DATSUN

Finally found some time to start inserting the 280z body side molding!

Last time I riveted the 280z side molding channels onto the body. Now it’s all about inserting the rubber molding. I ordered the 5/8″ rubber molding from CustomAutoTrim.com, and it came to my door in decent time. The size, perfect. The installation? Prepare to take some time to insert the rubber molding. It took a good 30mins to put on just one rubber molding!

What you’ll need to install:
1) 5/8″ Vinyl / Rubber molding (see previous post about 280z body side molding for sizes)
2) Razor
3) Something thin / plastic like a spatula or a guitar pick
4) Tape measure

First, making sure it’s sized correctly! Last time, I ordered in the incorrect one… This one from CustomAutoTrim – perfect.

“Measure twice, cut once” – no no, measure three times. Whenever my mom was showing us how to cook, she’d always say, ‘you can always add, but you can’t take away’. The methodology is still true here, but reversed – you can always take away, but you can’t add. So measure w/ a little excess, you can always trim the molding later. And since I ordered 16ft of molding, I should have some excess…but only for trimming, not enough to complete another channel if i completely screw up.

The vinyl / rubber molding is a tight fit, and getting in that channel can take some time. Here i’m using a guitar pick to help feed the vinyl / rubber molding into the 280z body side molding channel.

Another technique i found to work really well in getting the molding on was to bend the molding like the picture below. This actually allowed me to use the molding itself to help press fit it into the channel.

At the end, i was only left w/ a 1/4″ excess. A razor helped create a clean edge to butt up against the molding darts ends. Don’t mind the dirty car… after giving a nice wash and wax last sunday, i parked it in lot that ended up getting “cleaned”… meaning leaf blowers. ugh.

280z side molding completed! It’s a super clean installation that takes some time / effort, but really completes the period look.

My last post was about putting on the aluminum side molding channels with rivets, so now it’s time to pop in the rubber molding. However… it looks like the molding I purchased is NOT the right one.

Unfortunately, I ordered the incorrect rubber molding from BlackDragonAuto.com. I must have missed that the ‘Body Side Molding’ section was for a 280zx (1979-83), and just looked at the description for part# 97-650 “Adhesive Molding-Black, 16ft roll, cut to fit 280”. Oh well, we’ll try to get that returned if possible.

So I did a little research this morning, and found the CORRECT rubber molding is actually hard to find (neither MSA nor BlackDragonAuto sell it). ~~The proper rubber molding for the 280z can be found at CustomAutoTrim.com.~~

[Update, 9/12/24: CustomAutoTrim no longer sells this type of rubber moulding (hence the broken link), but have updated their stock to a slightly different shaped (round) albeit more flexible vinyl insert] updated link

This is the correct version because it locks into the side molding “stick” or channel, rather than be affixed by adhesive. CustomAutoTrim also sells the ends of the side molding channels, however the “bullet” and “chisel” ends used on the 280z seem to be discontinued at the time of this post.

If you’re looking for side molding for your 280z you’ll need (at least) the following lengths:

front fender: 23″ per side
door: 32 3/8″ per side
rear fender: 37 1/2″ per side

Total: 185.75″ = 15.48 ft = 16ft (since they sell by the foot) @ ~~$2.25/ft = $36~~

(Lengths serve as a guide only. Measure your Z for rubber moulding lengths)

[update, 9/12/24: prices haven’t changed that much! Price above was back in 2012. As of this writing it’s available in 7.5ft sections for $24 ($3.20/ft). Not bad!]

Tag: body side molding

280z Body Side Molding – Inserting the rubber molding

Body Side Molding – Rubber Molding